Why Learning Plumbing Basics is Crucial for Bathtub Installation
Why Learning Plumbing Basics is Crucial for Bathtub Installation
Blog Article
Each person seems to have their own piece of advice on the subject of How to Install a Bathtub.
Mounting a tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately hard job. If the old bathtub is readily obtainable, the project can relocate rapidly; if you need to open a wall to eliminate the old bathtub and also position the new tub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly need a helper to vacate the old tub as well as set in the new one. Make sure you have qualified on your own for the work as well as are comfortable trying it. As opposed to working with a contractor to take over a halfway-completed job, it is far better to consider using one before you start. Opportunities are you may need an expert plumber to make tube connections.
This article will certainly aid you set up a new bath tub in your washroom if you have currently acquired a new bathtub as well as do not need to transform the plan of your previous water supply pipelines.
Your tools and also material list need to consist of the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, activate the taps to drain pipes any water remaining in the system. The process of eliminating the existing taps can be fairly problematic because of the limited access that is commonly the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the taps. Have a cloth ready for the continuing to be water that will certainly come from the pipelines. When the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. When the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Before going on to fit the new faucets, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic connector to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end supplies a connection to the current supply pipelines.
If you require to fit a monobloc, then you will certainly call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin guaranteeing that the washing machines remain in area between the tap and also the sink. Protect the tap in position with the maker offered backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap ports. The previous type must be attached to the tap finishes initially, tightening only by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Bath tub
Using both wood boards under its feet, put the bath tub in the required position. The wood boards are valuable in evenly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 tiny points.
The following goal is to guarantee that the bath tub is leveled all round. This can be achieved by checking the spirit level and also readjusting the feet on the bath tub till the spirit level reviews degree.
To mount taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Turn on the supply of water and also inspect all joints and also new pipework for leakages and tighten them if essential. Fill the bath tub and likewise examine the overflow outlet as well as the regular outlet for leaks.
Ultimately, fix the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bath tub needs to wait until the bathtub has been utilized at the very least when as this will certainly resolve it right into its last placement.
Preparing for the Installment
First of all, the supporting structure supplied with the bathroom ought to be fitted (if called for) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps unit to avoid strain on the tub.
Fit the flexible faucet adapters to the bottom of both faucets using 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you utilize every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom must now prepare to be suited its last position.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to fracture an inflexible seal, causing the water to penetrate the wall in between the bath as well as the tiling, leading to complications with wetness and also possible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your components and fittings. They are offered in tubes and also cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the tub with water prior to securing, to enable the motion experienced when the tub is in use. The sealant can fracture rather very early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly available on the marketplace. It is recommended to fit the tiles making use of water-resistant or water-proof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been introduced to that report about How to Install a Bathtub from an acquaintance on a different site. Don't hesitate to take the opportunity to promote this blog entry if you appreciated it. I praise you for your time. Don't hesitate to come visit our blog back soon.
Emergency? Depend on our professionals. Report this page